LG Basic Lock


    Safes with this Lock:
  1. Various [early models]
    Early models that came standard with the LG Basic II are no longer available with this lock.

    IMPORTANT:
  1. To ensure the safety of your belongings, you MUST change the factory set code to your own unique code immediately!

FEATURES:

LG Basic
      User Code:
    1. Opens Lock
    2. Change Combination
      Wrong Entry Penalty
    1. Entry of 4 consecutive invalid codes results in a 5 minute delay period
      Low Battery Warning
    1. Repeated LED flashing & beeping during opening indicates battery is low & needs replacement
      Automatic Re-lock
    1. The controller will re-lock in 4 seconds after a valid entry is made and the door is open
      Audio & Visual Signal
    1. Double Signal : 2 flashes & 2 beeps - indicates entry is valid or accepted
    2. Triple Signal : 3 flashes & 3 beeps - indicates invalid or not accepted

OPERATING INSTRUCTIONS:

      Always perform this operation with the door open
    1. Before closing the door, make sure all the changes are correct.
      Opening the Lock
    1. Enter : Valid 6-digit Code
      [Factory set : x - x - x - x - x - x]
      Please see your user manual for the factory set Code or contact Tech Support.
      The lock will confirm a valid code entry with a double signal
    2. Within 4 seconds, turn handle to the open position
    3. Pull door open
      NOTE: Invalid Code Entry - Lock will signal 3 times
      Wrong-Try Penalty
    1. Entry of 4 consecutive invalid combinations starts a 5 minute delay period
      Light flashes Red at 10 second intervals
      Entry will not respond to any keystroke during delay period
    2. At the end of the delay period, 2 more consecutive invalid combinations will restart an additional 5 minute delay period

      NOTE:
    1. Verify the new master code at least 3 times before closing the door to make sure the code is correct.
    2. Operations between adjacent steps need be completed in 10 seconds. Otherwise, the lock system sets back to standby status.

      Changing Your Combination
      Always Perform this operation with the door open
    1. Enter : 0-0-0-0-0-0
    2. Enter : Existing 6-digit Code
    3. Enter : New 6-digit Code - New 6-digit Code
      If a mistake is made wait 30 seconds & repeat steps 1 - 3.
    4. Test lock operation several times before closing the door
      CAUTION: When selecting a Code do not use birthdays or other predictable data that could give correlation between the user & code. Keep the code secret.

      NOTE:
    1. Verify the new master code at least 3 times before closing the door to make sure the code is correct.
    2. Operations between adjacent steps need be completed in 10 seconds. Otherwise, the lock system sets back to standby status.

      Low Battery Warning
      Repeated beeping during an opening indicates that the battery is low & needs immediate replacement. Uses one 9V Alkaline Battery. LA GARD™ recommends the use of Duracell™ or Eveready™ Alkaline batteries. LA GARD™ recommends the replacement of batteries at least once annually. If battery is depleted and will not allow lock to open, simply follow instructions below. Lock contains a non-volatile memory, even with batteries removed the lock will retain all programming.

      Changing the Batteries Battery Compartments
      Small Battery Box:
    1. Remove black plastic battery compartment cover [located at the bottom of the keypad] by gently pulling downward on its handle.
    2. Allow the battery & its attached leads to drop down & out of the battery compartment. If it does not drop, gently pull on the battery until it does.
    3. Remove the connector by unsnapping it from the two terminals on the top of the battery.
      CAUTION! Hold onto battery terminal connector to avoid pulling the wires out of housing.
    4. Enter a valid Code to open the lock [see OPENING THE LOCK]
      NOTE: You must maintain battery contact at all times throughout the procedure.
    5. Change batteries as directed.
      The lock contains a non-volatile memory, & even with batteries removed, the lock will retain all programming.

Please contact Tech Support at 888.381.8514 for assistance.
Live Technical Support Available Monday - Friday 8:00am - 4:30pm [Pacific Standard Time]
Click Here to view our Mesa Safe Warranty.
Click Here to view our Limited Lifetime MBF Gun Safe Warranty.