Safes with this Lock:
1. Various Models : Upgrade
   This lock is an upgrade option on some safe models.

IMPORTANT:
1. To ensure the safety of your belongings, you MUST change the factory set code to your own unique code immediately!

FEATURES:

User Code
1. Opens Lock
2. Change Combination
Wrong Entry Penalty
1. Entry of 4 consecutive invalid codes results in a 5 minute delay period
Low Battery Warning
1. Repeated light flashing & beeping during opening indicates battery is low & needs replacement
Automatic Re-lock
1. The controller will re-lock in 4 seconds after a valid entry is made and the door is open
Audio/Visual Signals
1. Double Signal : 2 flashes & 2 beeps - indicates entry is valid or accepted
2. Triple Signal : 3 flashes & 3 beeps - indicates invalid or not accepted
Single & Dual User Mode
1. Single Mode : Open lock with 1 Code [Manager or User Code]
2. Dual Mode : Open lock with 2 Codes [Manager & User Code]
Time Delay & Time Window
1. Time Delay : A time period waiting for opening lock. The maximum Time Delay is 40 minutes
2. Time Window : A time period for entering code(s) to open lock after Time Delay. The maximum Time Window is 20 minutes

OPERATING INSTRUCTIONS:

Always perform this operation with the door open

1. Before closing the door, make sure all the changes are correct.

Opening the Lock
1. Enter : Valid Code [and insert eKEY, if set up]
   The lock will signal a valid combination entry with a double signal
2. Within 4 seconds, turn the keypad to the open position [clockwise] if using a dead-bolt style lock, or turn the handle to the open position if using a swing-bolt style lock.
3. Pull door open
   Invalid Code Entry : Lock will signal 3 times
Wrong-Try Penalty
1. Entry of 4 consecutive invalid combinations starts a 5 minute delay period
   Light flashes Red at 10 second intervals
   Entry will not respond to any keystroke during delay period


NOTE:
1. Verify the new master code at least 3 times before closing the door to make sure the code is correct.
2. Operations between adjacent steps need be completed in 10 seconds. Otherwise, the lock system sets back to standby status.


Changing Your Combination
Always perform this operation with the door open.
1. Enter : Existing Code & hold down the last digit until lock double signals twice & the light stays on
   If eKEY is set up - Enter : Existing Code then insert & hold eKEY until lock double signals twice & the light stays on
2. Press : 0
3. Enter : New Code - New Code [and insert eKEY, if set up]
   If a mistake is made wait 30 seconds and repeat steps 1 - 3
4. Test lock operation several times before closing the door.
   CAUTION: When selecting a code do not use birthday or other predictable data that could give correlation between the user and code. Keep the code secret.


NOTE:
1. Verify the new master code at least 3 times before closing the door to make sure the code is correct.
2. Operations between adjacent steps need be completed in 10 seconds. Otherwise, the lock system sets back to standby status.


Low Battery Warning
1. Repeated light flashing & beeping during an opening indicates that the battery is low and needs immediate replacement
2. Use only Alkaline Batteries [Example: Duracell ™ or Eveready ™ alkaline batteries]
3. Use one 9V Alkaline Battery in the Small Battery Box or six C-Cell Alkaline Batteries in the Large Battery Box
4. It is recommended that batteries be replaced at least once a year
If battery is depleted & will not allow lock to open:
5. Hold a new 9V Alkaline Battery on the contact points located on the front of the keypad
   [large battery terminal to large keypad contact; small battery terminal to small keypad contact]
6. Enter : Valid Code to open the lock [see OPENING THE LOCK]
   NOTE: You must maintain battery contact at all times throughout the procedure
7. Change batteries as directed below
   The lock contains a non-volatile memory, and even with batteries removed, the lock will retain all programming.
Changing the Batteries
Small Battery Box:
1. Open safe door
2. Remove battery box cover by pulling the front portion away from the safe door
3. Remove battery by unsnapping it from the connector
   CAUTION! Hold onto the battery connector to avoid pulling the wires out of the board.
4. Connect a new 9V Alkaline Battery to the battery connector
5. Push the battery & the leads completely into the battery compartment
6. Replace the cover & test the lock several times before closing the door
Large Battery Box:
7. Open safe door
8. Remove battery box cover by pulling the front portion away from the safe door
9. Remove the six old C-Cell Alkaline Batteries
10. Insert six new C-Cell Alkaline Batteries
11. Replace the cover & test the lock several times before closing the door.

Mounting Instructions available at www.kaba-mas.com.
Please contact Tech Support at 888.381.8514 for assistance.
Live Technical Support Available Monday - Friday 8:00am - 4:30pm [Pacific Standard Time]
Click Here to view our Mesa Safe Warranty.
Click Here to view our Limited Lifetime MBF Gun Safe Warranty.