MSL-50 Lock


FEATURES:

MSL-50
      Two Code Capacity
    1. User 1 Code:1 - 2 - 3 - 4 - 5 - 6 - 7 - 8
    2. User 2 Code: 1 - 6 - 8
      Lock-Out Penalty
    1. Five Beeps Lockout Penalty
    2. If three invalid codes are entered in a row, the keypad will shut down for a period of fifteen (15) minutes.
    3. During this shut down period the keypad will not accept any codes.
      Two User Codes
    1. Two User Codes can be programmed up to eight (8) digits long.
    2. Please change both codes immediately for your safety.

OPERATING INSTRUCTIONS:

      Always Perform this operation with the door open
    1. Before closing the door, make sure all the changes are correct.
      Quick Start
      image2
    1. Install a 9-Volt Battery
    2. Enter 1-2-3-4-5-6-7-8-#
    3. Turn handle before the green light turns off
    4. To lock your safe, close door & turn handle back to the locked position

      IMPORTANT:
    1. Always make sure your safe is locked before walking away!.

    1. If your code is correct a green light will turn on for approximately 5 seconds & you will hear a 'Click'
    2. If the code is in incorrect a red light will turn on, followed by 5 'Beeps'

      NOTE:
    1. Be sure to press firmly & ONLY use your finger tips to press the keys on the keypad. DO NOT USE your finger nail, a pen, etc. This will damage the keys

      Safe Operation & Programming
    1. 1st USER CODE is factory set to : 1-2-3-4-5-6-7-8-#
    2. 2nd USER CODE is factory set to : 1-6-8

      IMPORTANT:
    1. Because the codes are factory set, we highly recommend changing the codes to your own unique codes immediately!

      How To Open Your Safe
    1. Input : Code-# [light stays green for 5 seconds]
    2. Turn handle to the unlocked position before the green light disappears
      Example : 1-5-9-#
      Invalid Code : 5 'Beeps'
      Wrong Try Penalty
    1. If 3 wrong codes are entered consecutively, the keypad will shut down for a period of 15 minutes. During this shut down period, the keypad will not accept any codes
      Changing the 1st User Code
    1. Locate the red button on the inside hinge side edge of door
    2. Press the red button [Lock will 'Beep' 2 times with the yellow light on]
    3. Input : Your New Code-* [Lock will 'Beep' 2 times]
      Unsuccessful Code Change : 5 'Beeps' [the old code is still valid; repeat steps 1-3]

      NOTE:
    1. Test the new codes several times before closing the door.

      Changing the 2nd User Code
    1. Locate the red button on the inside hinge side edge of door
    2. Input : 0-0 on the keypad & Press the red button [Lock will 'Beep' 2 times with the yellow light on]
    3. Input : Your New Code-* [Lock will 'Beep' 2 times]
      Unsuccessful Code Change : 5 'Beeps' [the old code is still valid; repeat steps 1-3]

      NOTE:
    1. Test the new codes several times before closing the door.

      Low Battery Warning
    1. Red light appears when you open the safe other than the green light.
    2. Enter your code and get valid response but the lock doesn't unlock.
      Changing the Batteries image2
    1. Locate the battery cover on the bottom edge of the keypad and remove the cover by pulling on the tab.
    2. Carefully and gently remove the 9-volt battery from the compartment.
      CAUTION! Hold onto battery connector to avoid pulling wires out of housing.
    3. Carefully reinsert the new 9V alkaline battery, do not force the battery into the compartment.
    4. The lock will retain all current codes and settings.
Please contact Tech Support at 888.381.8514 for assistance.
Live Technical Support Available Monday - Friday 8:00am - 4:30pm [Pacific Standard Time]
Click Here to view our Mesa Safe Warranty.
Click Here to view our Limited Lifetime MBF Gun Safe Warranty.